NEC 2023 & NEC 2026 load calculations · licensed-electrician verification on every scopeestimates@reillyelectrical.com
Reilly ElectricalLoad Engineering & Project Scoping

Services & Costs · Standby power

Whole-Home Standby Generators, Transfer Switches & Load Shedding

What a standby generator really costs installed in 2026, how air-cooled and liquid-cooled units compare, how the two big brands differ, and how NEC 702.4 load shedding avoids paying for kilowatts you will never use.

Standby generator enclosure installed outdoors
$10,000 – $15,000+14–24 kW air-cooled, turnkey

Air-cooled or liquid-cooled

Air-cooled (14–26 kW)Liquid-cooled (30–48 kW)
Typical turnkey cost, 2026$10,000 – $15,000+$16,000 – $30,000+
EngineSingle or V-twin, air-cooledAutomotive-style, radiator cooled, lower RPM
Best forMost homes up to ~4,000 sq ft with gas heat or load managementLarge all-electric homes, multiple A/C units, small commercial
Noise & serviceLouder; maintenance yearlyQuieter; longer service intervals
PadComposite or small concrete padPoured concrete pad

Where the money goes

Line itemTypical 2026 range
Generator unit (14–24 kW air-cooled)$4,000 – $6,500
Automatic transfer switch (200 A service-rated)$1,000 – $1,800
Electrical labor & materials$1,500 – $2,500
Gas or LP piping, regulator$500 – $2,000
Composite or concrete pad$400 – $1,000
Permits & inspections$250 – $600
Turnkey total$10,000 – $15,000+

LP tank purchase or lease is extra. Your gas utility may also need to upsize the meter for a large generator; that fee is theirs, not the installer's.

Standby generator enclosure installed outdoors with fuel piping
Clearances from windows, doors and the property line are set by the manufacturer, local code and NFPA 37.

Generac and Kohler: how they differ

Most US homes with a standby unit have one of these two brands. Both make reliable equipment; the right choice usually depends on the local dealer more than the logo.

Generac (Guardian series)Kohler (residential)
Dealer networkLargest in the US; easiest to find serviceSmaller but strong in many regions
EnclosureAluminum on many current models (composite on some)Steel or aluminum depending on model
Power qualityRated for sensitive electronicsOften marketed on low total harmonic distortion
Natural gas outputRoughly 10% below LP rating on air-cooled unitsSimilar; check each model's NG figure
Load managementSmart Management Modules (SMM), load shedding built into ATSLoad shed kits and power management modules

NEC 702.4 load shedding: the cheapest kilowatts you will buy

NEC 702.4 requires an optional standby system to have adequate capacity for the load it will carry — or an automatic load management system that keeps it from overloading. That second route is what lets a 24 kW air-cooled unit run a house that would otherwise need a 32–38 kW liquid-cooled one.

  • Modules cost $200–$500 each plus labor, typically one per large 240 V load (A/C, range, dryer, water heater, EV charger).
  • They shed loads in priority order and restore them when capacity returns, so the household barely notices.
  • Stepping down one or two tiers usually saves $3,000–$5,000, and more when it avoids a liquid-cooled unit and its heavier pad and larger gas line.

Soft starters for A/C compressors

A central A/C compressor can draw five or more times its running current for a second at start. A soft starter ($300–$600 installed) cuts that surge by around 60% and is often the difference between a 22 kW and a 26 kW unit.

Size it before the dealer does

Run the generator sizer with your fuel, HVAC and heavy loads, toggle load shedding, and print the sheet to compare dealer quotes on equal terms.

Get a scoped quote, not a guess

Send your NEC load sheet, panel brand and ZIP code. A licensed local master electrician confirms the numbers on site, pulls the permit and quotes the real job.